Get notified
← Journal
Build update 3 / 17 November 2026

Your questions, my answers.

Since the Ronin 4D video went up, the questions came in: under the video, on EOSHD, in the DJI forum and in the Ronin 4D Pros group on Facebook. Here they are in one place, plus a few I would ask myself.

Sensors

Do the sensors stay clear?

The one in the middle is completely clear. The rails partly cover the two side by side ones, but never both at once. Straight down always stays open, and when the camera tilts, one of them still sees the ground. Z axis keeps working.

Tripod

Can't I just screw a normal tripod plate on?

You can, it takes five seconds. I did it for years: a Manfrotto plate on the front of the stock plate. Always back heavy, always drifting, because the middle is where the sensors sit. Put a plate there and you cover the sensors the Z axis depends on.

Handheld

Isn't the 4D made to be handheld?

A gimbal can fake a locked off shot. But on a long interview you end up holding it at eye level, dreading every extra question. That's what the tripod is for.

Quick release

Why Manfrotto and not Arca?

On purpose. Arca plates are mostly made for mirrorless bodies, with the rail running left to right across the camera. I don't trust Arca, or most heads with an Arca clamp, with a fully kitted 4D. Most fluid heads from prosumer up take the Manfrotto plate, so I know the head holds it. I'd rather nobody breaks a small travel tripod, and their camera with it.

Mic position

Why not put the mic on the top handle?

Because the head never stops moving. It's always looking around. Anything on top ends up in the shot or in front of the screen, and it hears the motors. Down at the front, the mics point where the lens points.

In frame

Do the mics end up in the shot?

With my 9mm pointing straight down, they can. But you'd have to hold the camera at a really odd angle. Long before that the gimbal hits its end stop or the head touches the lower bracket, so you tilt the whole camera down anyway, and they're out of frame again.

Vibration

No shock mount. Don't you hear vibration?

No problems so far. The printed part takes out the big vibrations, and the mics sit far from the motors and from your hand. Sony's FX6 top handle barely isolates its mic either, and it works fine, often better than a small shock mount. Fixed is stronger and lasts longer. The one thing you do hear is the follow focus motor on a hard rack, and no isolator fixes that.

Flex

Does the bracket block the release for the Flex?

No. I use the Flex cable with it all the time. I have a quick release on top of the mic bracket, so I pop the bracket off, press the release and put it back. Without that quick release the bracket sits low enough to reach the button directly.

Mics

Which mics are those?

Two Rode NT5s, a matched pair, on the stereo bracket.

Material

What is it made of?

The plate is aluminium, machined in Germany and black anodised. The brackets are printed.

Weight

And the weight?

Fair, the 4D is heavy, and that one I haven't fixed. The plate weighs 250 g, the stereo bracket 30 g and the mono bracket 15 g, all measured on the final parts.

Next

What comes next.

The final plates are back from the mill. Proper photos, and where the first review samples go, in the next update. Pre orders open soon after that. Part two of the Ronin 4D video is out now, with every other mod on my 4D. Keep the questions coming, under the videos or by replying to a build update. If you want to know when the shop opens, the signup is below.

Nick, Überlingen

From the workshop

Know when
the parts are ready.

One email when the shop opens. Or choose occasional build updates along the way.

Get notified

Choose your emails on the signup page. Unsubscribe any time.